Shop by Category

WATERPROOFING TERRACE KYRO ELASTIK FLEX RED 5/A 14L

Out Of Stock
-11%
46,95 € (IVA Included)
41,95 € (IVA Included)

Short Descriptions

1.- DESCRIPTION OF WATERPROOFING

Paint consisting of very hard elastic resin, for the protection and waterproofing of porous work surfaces.

2.- RECOMMENDED USES

Applicable on plaster, cement, brick, etc...

Protection and waterproofing of porous surfaces.

Exterior Interior.

Waterproofing and protection of outdoor surfaces

3.- PROPERTIES

Waterproof anti-leakage.

Good adherence to construction supports.

Excellent elasticity.

Shock resistant and passable.

Easy troubleshooting.

Does not accumulate weight on the structure.

Avoid risks as it is a water-based product.

Avoid works. Excellent support for tiles.

Resistant to the passage of time.  Meets watertightness standards.

Evaporative drying.

Details

1.- DESCRIPTION OF WATERPROOFING

Paint consisting of very hard elastic resin, for the protection and waterproofing of porous work surfaces.

2.- RECOMMENDED USES

Applicable on plaster, cement, brick, etc...

Protection and waterproofing of porous surfaces.

Exterior Interior.

Waterproofing and protection of outdoor surfaces

3.- PROPERTIES

Waterproof anti-leakage.

Good adherence to construction supports.

Excellent elasticity.

Shock resistant and passable.

Easy troubleshooting.

Does not accumulate weight on the structure.

Avoid risks as it is a water-based product.

Avoid works. Excellent support for tiles.

Resistant to the passage of time.  Meets watertightness standards.

Evaporative drying.

4.- TECHNICAL CHARACTERISTICS

Nature: pure acrylic dispersion

Appearance: Semi-matte.

Texture: Fine and elastic.

Colour: White and red

Pigments: Titanium dioxide and inorganic pigments with maximum resistance to weathering.

Specific gravity: 1.28 +/- 0.05

Volatile organic compounds (VOC): 11.90 g/l.

Vertical surfaces: 0.75 l/m2 (approximately 2-3 coats).

Horizontal surfaces: 1.5-2 l/m2 (approximately 3-4 coats).

Drying (20ºC HR: 60%): to the touch: 2-4 hours

5.- APPLICATION SYSTEMS

Diluent: Water.

Tools/ Dilution:

Brush: 0- 5% max.

Roller: 0- 5% max.

Airbrush gun: 0-15% max.

Turbo low pressure: 0-15% max.

Airless: 0- 5% max.

Air mix: 0-10% max.

Repainting (20º C, RH 60%):

Minimum: 24 hours.

Max: It doesn't have.

Cleaning: Water immediately after use.

6.- PREPARATION OF NEW SUPPORTS

Cement mortar: Wait until fully set (30 days minimum). Clean the support of possible efflorescence by abrasive blasting, as well as neutralize alkaline surfaces. On excessively polished surfaces, sand to open the pore. Fix the crumbly supports with a suitable fixative. Clean the support of foreign products and/or residues.

Plaster: Wait until it is completely dry (max. 20% humidity). Remove foreign products and/or residues from the support. Eliminate efflorescence. Regulate the absorption of the surface by sealing primer or matte paste. On excessively polished surfaces, sand to open the pore. Fix the crumbly or floury supports using a suitable fixative.

7.- RESTORATION AND MAINTENANCE.

1. Completely remove old paint in poor condition or poorly adhered.

2. Glossy surfaces should be matted to ensure good adhesion.

3. On painted supports, the solidity and anchoring of the paint must be checked, its nature diagnosed to avoid possible incompatibilities and dust and dirt must be removed before being repainted.

4. Putty the defects of the support with putty.

5. On moldy walls, treat previously with fungicide.

6. Recommended consumption on already waterproofed surfaces: 1st Layer 0.35 l/m2. 2nd Layer 0.35 l/m2.

8.- APPLICATION

Sanitize the surface by removing all kinds of dirt, moss, mold, etc. from the surface and wash with clean, uncontaminated water. Shake the product until it is perfectly homogenized.

Slightly dilute the product depending on the porosity and state of the support in the first layer.

It is advisable to place a gridded fiberglass mesh of 80 gr/m2 immediately after applying.

Finish in several layers until applying the recommended amount.

It is very important that the application temperature and that of the support is greater than 5ºC.

9.- GENERAL OBSERVATIONS

The product is adapted to waterproof the support by applying it between the humidity and the surface to be protected.

Avoid applying the product on unstable days with risk of rain.

Use to dilute clean, uncontaminated water.

Outdoors use suitable putties.

The gridded fiberglass mesh must adapt to the support, leaving gaps in the expansion joints. The recommended coverage for horizontal surfaces is 2 l/m2 applied in a minimum of 3-4 coats. Do not store diluted product.

Avoid exposing the containers to both high and low temperatures.

Recommended maximum storage time: 30 months from manufacture in its original, perfectly closed container, under cover and at temperatures between 5 and 35º C.

In unfavorable weather conditions it is preferable to apply in a greater number of hands.

It is convenient for its conservation to avoid adding water to the product that is not going to be used in the application. Consult and comply with the applicable regulations.

10.- SAFETY AND HYGIENE – PROTECTION OF THE ENVIRONMENT

Do not eat, drink or smoke during its application.

In case of contact with eyes, wash with clean and abundant water.

Toxic by ingestion.

Keep out of the reach of children.

Do not pour waste down the drain.

Keep the product in dry areas

×